LCD Separator Glass Repair Machine LED Display Glass Touch Separator

Touch Screen Separator LCD Panel Glue Disassembly Machine for iPhone / Samsung / HTC / Sony etc.

Features:

1) Just place the LCD display on the heating panel, turn on the "Vacuum Pump" switch, then you can separate the glass. And the LCD screen is firmly fixed on the panel during separation.

2) The vacuum LCD separator shell is made of metal. And it is better than the LCD separator with vacuum backlight.

3) The Vacuum LCD separator is equipped with four bearings. It is more convenient when separating;

4) The surface of the heating plate is very smooth. It securely holds the broken LCD display;

5) The LCD separator has non-slip mounting seats. It makes your work smooth and reduces the chance of damaging the LCD assembly.

6) This machine set can help separate the cell phone touch screen from the LCD display or the touch screen from the front glass lens.

Technical specifications:

1) Operating Voltage: 110v-240v

2) Front LCD screen separated

3) Automatic machine for hot separator plate

4) Low noise, affordable and practical

5) Fast, high efficiency, and easy to use

6) LCD separator machine with vacuum pump inside for iPhone, Samsung, HTC, LG, glass repair

7) This machine comes with the vacuum pump inside to suction the LCD display onto the heating plate so you don't have trouble clamping the LCD screen. This is the latest model suitable for any side of the phone LCD

8) Works with:

All iPhones

Samsung Galaxy

Samsung Galaxy Note

Samsung Galaxy Mega

HTC Phone

LG Phone LCD

Not suitable for Curved screens

Nokia and some other cell phones

Brief introduction:

1) Just place the LCD display on the heating panel, turn on the "Vacuum Pump" switch, then you can separate the glass. And the LCD screen is firmly fixed on the panel during separation.

2) The LCD screen separator is used to separate the glass lens, touch screen, and LCD display assembly for Apple, Samsung, HTC, and other cell phones.

If you need molds or other accessories for iPhone, Samsung Galaxy. Please contact me before placing the order.

As current cell phones trend, Apple, Samsung, and HTC, many new cell phones are made of screen assembly. - Since the glass lens, touch screen, and LCD are connected to each other, separating the broken or cracked screen by hand is difficult if it happens. You always have to take it to the repair shop. The cost is high and the time is long. Or you need to buy an expensive equipment package, including separate machines, SMT machines, laminators, and bubble removal machines.

- But now you can easily handle it. We have developed the machine and skills, there is no need to buy expensive equipment and large spaces for general repair workshops. After learning the skills, you can replace an old screen within 30 minutes and it will look like new.

Package contents:

1 LCD vacuum separator

1 x Cutting line

1 x Power cable

Instructions:

Temperature adjustment: (recommended exercises three times for a bad separation of the apple screen (100 degrees) is set at 100 degrees, heating, press the screen upwards, press the screen also you will feel the hand pressure can be separated (--- in addition to plastic - on glue - polymerization) repeated three times, and then make a good screen.

1) Divided:

Key point 1 on the screen principle (fast below). 2 Cut the wire to make the bottom shelf, below the screen level, - when the dropdown menu Don't worry, slowly about (size) to a large one, pull down until the separation (one not) can return the knife two or three times, until you feel separated, then lift the line. The video is to watch these key points inside the action: don't worry when the dropdown is a steel wire to connect the cylinder near the dropdown cursor, radiant not large, then pull widely.

2) In addition to plastic:

Support glue solution is a special dedicated one, after the separation of the adhesive glue solution slowly with a clean cloth to clean.

3) Hollow glue:

Due to the impact on the finished effect of the plastic screen, so to practice more, the amount of words cannot be said clearly. As long as they go full screen on the line. Skills, (to avoid bubbles there, when we have to put the glass slowly, watch the glue, don't let it have a bubble, don't put hand pressure, and let it sink slowly. wait for the glue itself to go on the whole screen.)

4) Care

Key point of the polymerization process: the good of the screen according to the polymerization lamp for 1-2 minutes, then extract (this process is called pre-cured), the clean side of the glue, and then put the photopolymerization, generally polymerizing 8 - 15 minutes.